- Contact Us
I have go through the instructions from here until Step Four.
I encounter the problem as when I enter the site I get my router's admin page.
I have no idea how to solve the problem with the three options:
1) If supported, move the admin page to a different port
2) Forward a different port
3) Try a firmware upgrade, or alternative firmware (DD-WRT, OpenWRT etc) where supported
I have done with the port forwarding intranet, which I can view my cctv using LAN on other PC.
Can anyone please help me?? I'm not so sure about the setting on NAT (Virtual Server and DMZ). Is it something to do with the stated setting? I have tried to put Local IP of the CCTV PC, but no Luck..
I'm using Billion BiPac-5112S (Modem) which connected to wireless router (Dlink-DIR615).. Port Forwarding was done on the router.
Answer by My Udin · Mar 31, 2010 at 03:27 PM
Dlink Wireless 192.168.0.50
change ip dlink wireless 192.168.1.50 gateway refer ip billion 192.168.1.254, so dlink wireless can connect internet
dvr set ip 192.168.1.xxx
NAT billion set port dvr and ip dvr
Answer by bengkelfifa · Apr 12, 2010 at 12:02 PM
saya punya modem wifi prolonk IP : 192.168.1.254 speedy sudah sy daftarkan di dyndns & dpt IP : 184.108.40.206 DMZ Modem sudah sy kasih 220.127.116.11
IP DVR : 192.168.1.100 Subnet mask : 255.255.255.0 gateway : 192.168.0.1 HTTP Pport : 80 Command Port : 5050 Media Port : 6050
Setiap sy panggil 18.104.22.168 kenapa selalu masuk ke modem??? kok gak masuk ke CCTV.... tolong bantuannya.... thanks.....
Answer by RotBlitz · Mar 27, 2010 at 02:08 PM
You need to forward the desired port on both, your modem and your router, from your modem to the WAN facing internal IP address of your router, and then from your router to the internal IP address of your CCTV device. At this point you can also translate the port number from one (external) to another (internal), the latter where your CCTV device is listening on. If this port does not work, because you get an admin interface of your modem or your router, simply use another port number.
Answer by hincctv · Mar 28, 2010 at 08:49 AM
Thank you so much RotBlitz.
BUT I'm still confused..
My Modem IP (192.168.1.254) My Wireless Router IP (192.168.0.1) CCTV (192.168.0.50) using Port 8080 and 8081.
SO when I do Port Forward in Router, I should Port-Forward / set 192.168.0.50 on my router rite? Do I need to do Port Forward to Modem IP on my Wireless Router as well?
I have set NAT in my Modem to 192.168.0.1.
Answer by RotBlitz · Mar 28, 2010 at 09:55 AM
This is an example how it would work:
Modem Router CCTV [192.168.1.x Net] [192.168.0.x Net] Fw::8080 -> 192.168.1.???:8080 Fw:192.168.1.???:8080 -> 192.168.0.50:8080 Fw::8081 -> 192.168.1.???:8081 Fw:192.168.1.???:8081 -> 192.168.0.50:8081 (Port translation is possible here.)
Not sure about the WAN facing IP address of your router, but this may be 192.168.1.1.
cctv system set up 1 Answer
port forwarding internal external 2 Answers